- #CYBERPOWER BATTERY BACKUP SOFTWARE INSTALL#
- #CYBERPOWER BATTERY BACKUP SOFTWARE SOFTWARE#
- #CYBERPOWER BATTERY BACKUP SOFTWARE PC#
#CYBERPOWER BATTERY BACKUP SOFTWARE SOFTWARE#
The SoftwareĬyberPower supplies the PowerPanel Personal software package for free. The parasitic power draw of the UPS when the batteries are charged is extremely small, at less than 1.5 Watts when the LCD is also turned off. Once turned off, there is no voltage on any of the outputs of the UPS. It does not really affect the RMS output of the unit over time but the instability of the timing circuitry on a brand-new unit is peculiar. Every 1.5 second or so, the output voltage is slightly boosted, reaching up to nearly 1200V peak-to-peak for less than 100ms. One undesirable effect we noticed regarding the output of the CyberPower ValuePro VP1600ELCD 1600 VA is that the output is not perfectly stable over time. The RMS voltage value of the output always remains stable at 230V.īattery Output Waveform - 20% load, 3 second period The output waveform shifts greatly as the load increases but it basically always remains a two-step square wave. The peak-to-peak voltage of this waveform is over 1000 V due to these peaks but they are too short to cause any kind of damage.īattery Output Waveform - 50% load (left) / 100% load (right)Īs is the case with such designs, the circuitry of the CyberPower ValuePro VP1600ELCD 1600 VA adjusts the timing of the MOSFETS to maintain a stable output. There is a momentary peak at the front of the second step, which is extremely high but also very short. It does not even resemble a sinewave – it is but a two-step square wave that ultimately produces a 230 V RMS output. Depending on the manufacturer and cost of the product, designers will make the corresponding effort to simulate a true sine wave as much as possible.Īs expected from a UPS at this price point and with such a high power output, the output quality while on battery backup is quite poor. The better the circuitry design, the more the steps, thus the better the approximation to a true sine wave output. This approximation typically is a ladder wave with a few steps. What that means is that the output will not be close to the standard sine wave that we receive from grid, but an approximation of it. The CyberPower ValuePro VP1600ELCD 1600 VA is a unit with a “modified sine wave” output. These figures are achieved with the batteries fully charged while they are still brand new. These times are great considering the UPS also lacks any active cooling.
#CYBERPOWER BATTERY BACKUP SOFTWARE PC#
In theory, the UPS can hold a lightly loaded typical PC for over than half an hour. The runtime is well over two hours with a load of 50 Watts, a little over 10 minutes with a load of 500 Watts, and slightly less than 2 minutes with the UPS fully loaded. Our load testing reveals that CyberPower’s running charts are quite accurate. There are minor frequency variations but these are exceptionally small.
The RMS voltage and frequency output look to be extremely close to the expected 230V/50Hz output. The transfer times are exceptional, with the unit requiring less than 4 ms to switch while fully loaded. Once I did the above, communications were restored and the status box returned.The basic electrical figures of the CyberPower ValuePro VP1600ELCD 1600 VA UPS are quite good – unexpectedly so, in fact. Exit the connection to your pfSense box.Run these two commands: $ /usr/local/sbin/upsdrvctl -u root start.Login via Terminal to the pfSense box, then use item (8) to exit to the shell.If there happens to be more than one person out there with my setup, and your CyberPower UPS isn't talking to the NUT plug-in in pfSense, here's the fix:
Today I found it, so also today, it goes on my blog so I'll always know where it is… I knew I had a fix for this issue somewhere, but I couldn't remember where.
#CYBERPOWER BATTERY BACKUP SOFTWARE INSTALL#
Within pfSense, you can install the Network UPS Tools package (called NUT in pfSense) to monitor and report on the UPS here's how it looks in the overview screen:Īfter recently updating to a newer Protectli box, however, all I saw was a message that read "Cannot communicate with UPS" (or something close to that). Our home router is a Protectli box running pfSense firewall/router software the Protectli box is connected to a CyberPower UPS. This post is probably of interest only to me, and I'm posting it just because I'm getting tired of remembering where I stored this tidbit on my Mac.
0 kommentar(er)
